Floors worth looking down at, Autryville.
Resin floors and countertops around Autryville, poured by the owner, Beto Ponce. Insured and bonded, with metallic work as the specialty.
Insured and bonded · 5 years · every floor poured by the owner
Get a free quote
Photos and rough square footage get you a real number.
Resin floors for Autryville homes.
Most of the garages we coat around Autryville were poured with the house and never touched since.
We run out to Autryville from the shop in Goldsboro, about 40 minutes out. Autryville is in Sampson County, and we cover the towns around it too, including Clinton, Newton Grove, Turkey, Garland.
Concrete is porous. It drinks oil, it dusts under tires, and once a stain is in there it stays. A resin floor closes the slab off for good.
Beto came to epoxy from land clearing and excavation, and it shows in how much of every job goes into the slab itself. Each floor gets a diamond grind down to open concrete, the cracks get chased and filled, and then the pour and topcoat go on. He owns the grinding equipment so that step never gets cut short.
What eastern North Carolina does to a slab.
Humidity is the one that surprises people. Coastal plain slabs sit on sandy soil with a water table that moves, and a slab poured without a vapor barrier will push moisture up through itself for its whole life. That vapor has to go somewhere. If it meets a coating that cannot breathe, it collects underneath and lifts it, which is what people are describing when they say a floor bubbled or peeled in sheets.
A floor that lifts a year after it went down costs the homeowner and the installer both. That is why testing happens before the quote here, never after. If the reading says wet, we price a system that can take it. If it is bad enough that no coating should go on, we will tell you before you spend anything.
The other local factor is heat. Resin cures by chemical reaction and the reaction runs faster when it is hot. A July pour in an uninsulated Autryville garage gives you less working time than the same pour in October, which matters most on metallic floors where the pattern is set while it is wet. We plan around it instead of fighting it.
What we pour in Autryville
Recent pours
Which rooms we end up in.
Garages are the bulk of it. A two-car bay is the job we quote most weeks, and the reason is usually the same: the slab has started dusting, or there is a stain by the driver's door that will not come up no matter what gets poured on it.
Plenty of people who call about a garage end up asking about the kitchen. Countertops are the other side of the business: resin goes over your current counters, so your Autryville kitchen looks brand new while the cabinets and plumbing stay exactly where they are. You can read how we pour countertops before you call.
Timing a pour around the weather.
If you want a spring or fall date, call early. Those mild months give resin the widest working window, so they fill up first every year. The rest of the year still works. Summer pours just get scheduled for the early part of the day, and winter pours go ahead once the slab is warm enough.
What moves the price.
The least expensive floor we do is a clean, solid slab that has never been coated. Anything else costs more because it means more prep, whether that is cracks to chase or a failed coating to grind off. Prep is the bulk of the labor on any job, so the slab’s shape matters about as much as its square footage.
Once we start, the number does not change. We set it the day we walk the slab, after we have seen the cracks and the old coating in person. Want a gut check before anyone drives out? Send a few photos and we will tell you whether you are in the right range.
How the two days run.
Day one is prep. Grinders and dust extraction come off the trailer and the slab gets taken down to clean concrete, then the cracks and pits that the grind exposes get chased out and filled. It is loud and it is dusty, and it is most of the labor in the job. Day two is the pour and the topcoat, which is the fast half.
The room has to be completely empty the morning we start, because we grind the whole slab rather than working around things. Light foot traffic is fine the next morning. Vehicles go back on at day three or four depending on how warm it is, and rushing that is the one shortcut that will mark a brand new floor.
Who actually pours it.
Beto Ponce does the pours himself. The person who quotes your floor is the person standing on it with a squeegee.
Insured and bonded, 5 years of pours, and a phone the owner answers. See the gallery, read about the rest of Sampson County, or send photos of the slab.
The same person who answers the phone drives the trailer out, so the question of whether we come to you is easy to settle. Autryville is well within the 10 counties we cover from Goldsboro. If you are a few miles beyond town, call before you assume we will not come. Town limits rarely line up with the real drive.
Questions from Autryville customers
What if I already have a coating that is failing?
That is a normal starting point. It comes off in the grind, and what is underneath decides what the job actually is. We would rather find that on day one than after.
Do I have to coat it after grinding?
No, the coating is optional. We grind slabs that never get coated, then seal them and call it done. Shop floors are a common example, along with any concrete the owner likes as it is.
Will grinding get rid of the oil stains?
It depends how deep the oil went. Surface stains come off with the top layer when we grind. Oil that has soaked well into the slab can show up again later, which is why those floors get degreased and sometimes primed.
How much dust does it make?
Far less than people expect. The grinder runs into a dust extractor at the tool, so the dust is captured where it is made rather than filling the house. It is not zero, but it is not the fog people picture either.
How long does a garage floor take?
The work itself is two days on most two-car garages, and the slower part is the curing. You can walk across it the morning after we coat it. Parking has to wait three to four days. Day one of the job is the grind and prep, day two is the coating.
Got a slab in Autryville?
Photos plus an approximate square footage gets you a straight answer on what the floor will take.
Look at real floors in the gallery, then call. Beto Ponce answers, and he is the one who would do the work.
(919) 440-1333