Resin floors across Greene County.
The closest county east. Small towns, big garages, a lot of word of mouth. Poured by the owner, ground down to clean concrete first.
Insured and bonded · 5 years · every floor poured by the owner
Get a free quote
Photos and rough square footage get you a real number.
What we install around Greene County.
The closest county east. Small towns, big garages, a lot of word of mouth.
Snow Hill sits about 25 minutes from the shop in Goldsboro, well inside the 60 mile radius we cover. We cover Snow Hill and the communities between them: Snow Hill, Hookerton, Walstonburg.
Garages are the bulk of the work, but a good share of what we pour in Greene County is countertops, because resurfacing a kitchen costs a fraction of replacing the counters and takes two or three days instead of two weeks.
Whatever the room is, the sequence does not change. We grind the slab down to open concrete, fix what the grind exposes, then pour. Read more about how we prep concrete or tell us what you are looking at.
Towns we cover in Greene County
Work from around the county
Which floor belongs in which room.
Flake is the workhorse. Vinyl chip broadcast into the base coat and locked under a clear topcoat, it hides tire marks and dust and gives you grip when the floor is wet. Most garages around Greene County end up here once people have seen both options in person.
Metallic is the showpiece. Pigment moves while the resin cures, so the pattern is decided in the twenty minutes the floor is still workable and no two come out the same. Quartz is the toughest thing we install, graded sand set in resin with slip resistance built into the texture, and it belongs in laundry rooms, workshops, and anywhere water and traffic show up together.
Countertops are their own category. The resin pours over the counters you already have, so a kitchen changes completely without a tear-out. Read more on the countertops page.
What we pour
What the ground here does to a slab.
This is coastal plain country. Sandy soil, a water table that moves with the season, and eight months a year of real humidity. Slabs poured on that ground shift a little, and the hairline cracking that comes with it is normal rather than alarming. What matters is catching it during the grind and filling it, instead of coating straight over it and watching it telegraph through the finish six months later.
The bigger issue is vapor. A lot of the housing stock around Greene County went down without a vapor barrier under the slab, because for years that was normal practice. Those floors push moisture upward every day, and a coating that cannot breathe traps it and lifts. We test before quoting. If a slab is too wet for the system you want, we will say so and price something that can handle it.
How a job in Greene County runs.
Everything comes out on a trailer: grinders, dust extraction, mixing gear and material. Day one is prep, which is the loud and dusty half. Day two is the pour. You can walk on it the next morning and put a vehicle back on it in three to four days depending on temperature.
The garage needs to be completely empty the morning we start, because we have to grind the whole slab. That is the one piece of the job that falls on you, and it is worth doing the weekend before rather than the morning of.
Questions from Greene County customers
Is there a warranty?
Yes, and it is worth reading rather than framing. Ask when we quote and we will tell you plainly what it covers and what it does not.
How far out are you booking?
It moves with the season. Spring and fall fill first. Call and we will tell you honestly where you would land rather than telling you what you want to hear.
What if I already have a coating that is failing?
That is a normal starting point. It comes off in the grind, and what is underneath decides what the job actually is. We would rather find that on day one than after.
Do I have to coat it after grinding?
No. Plenty of people grind and seal and stop there, especially on a shop floor or a slab they like the look of. Grinding is a service on its own, not only a step toward a coating.
Will grinding get rid of the oil stains?
It removes the stained surface layer, which handles most of it. Oil that has soaked deep into the slab can ghost back, so heavy contamination gets a degreasing pass first and sometimes a primer.
Working in Greene County this month.
Send a photo of the slab and the rough size. You get a number the day we look at it.
Call and you get Beto Ponce, not a call center. Or look through the gallery first.
(919) 440-1333