Resin floors across Wilson County.
Older brick homes with garages that were never finished past the slab. Poured by the owner, ground down to clean concrete first.
Insured and bonded · 5 years · every floor poured by the owner
Get a free quote
Photos and rough square footage get you a real number.
What we install around Wilson County.
Older brick homes with garages that were never finished past the slab.
Wilson sits about 35 minutes from the shop in Goldsboro, well inside the 60 mile radius we cover. We cover Wilson and the communities between them: Wilson, Black Creek, Lucama, Stantonsburg, Saratoga, Elm City, Sims, Sharpsburg.
Garages are the bulk of the work, but a good share of what we pour in Wilson County is countertops, because resurfacing a kitchen costs a fraction of replacing the counters and takes two or three days instead of two weeks.
Whatever the room is, the sequence does not change. We grind the slab down to open concrete, fix what the grind exposes, then pour. Read more about how we prep concrete or tell us what you are looking at.
Towns we cover in Wilson County
Work from around the county
Which floor belongs in which room.
Flake is the workhorse. Vinyl chip broadcast into the base coat and locked under a clear topcoat, it hides tire marks and dust and gives you grip when the floor is wet. Most garages around Wilson County end up here once people have seen both options in person.
Metallic is the showpiece. Pigment moves while the resin cures, so the pattern is decided in the twenty minutes the floor is still workable and no two come out the same. Quartz is the toughest thing we install, graded sand set in resin with slip resistance built into the texture, and it belongs in laundry rooms, workshops, and anywhere water and traffic show up together.
Countertops are their own category. The resin pours over the counters you already have, so a kitchen changes completely without a tear-out. Read more on the countertops page.
What we pour
What the ground here does to a slab.
This is coastal plain country. Sandy soil, a water table that moves with the season, and eight months a year of real humidity. Slabs poured on that ground shift a little, and the hairline cracking that comes with it is normal rather than alarming. What matters is catching it during the grind and filling it, instead of coating straight over it and watching it telegraph through the finish six months later.
The bigger issue is vapor. A lot of the housing stock around Wilson County went down without a vapor barrier under the slab, because for years that was normal practice. Those floors push moisture upward every day, and a coating that cannot breathe traps it and lifts. We test before quoting. If a slab is too wet for the system you want, we will say so and price something that can handle it.
How a job in Wilson County runs.
Everything comes out on a trailer: grinders, dust extraction, mixing gear and material. Day one is prep, which is the loud and dusty half. Day two is the pour. You can walk on it the next morning and put a vehicle back on it in three to four days depending on temperature.
The garage needs to be completely empty the morning we start, because we have to grind the whole slab. That is the one piece of the job that falls on you, and it is worth doing the weekend before rather than the morning of.
Questions from Wilson County customers
Can you coat a floor that already has something on it?
Usually. Old paint, failed sealer, and most previous coatings come off in the grind. If there is a moisture problem underneath we will tell you before we quote it, not after.
Is it slippery when wet?
A smooth topcoat is slick wet, same as polished concrete. For garages, patios and pool decks we broadcast an aggregate into the topcoat so it grips. Say the word and we will spec it.
How much does a floor cost?
It depends on square footage, the shape the slab is in, and which system you want. We quote off the actual floor, not a phone guess. Call (919) 440-1333 and we will come look.
Do you work in cold weather?
Resin cures by chemical reaction and the reaction slows down when the slab is cold. We work most of the Carolina winter, but we watch the slab temperature and will move a date rather than pour into conditions that will hurt the finish.
How long will it last?
A properly prepped residential floor is a ten to fifteen year surface. The ones that fail early almost always failed at prep, not at the resin.
Working in Wilson County this month.
Send a photo of the slab and the rough size. You get a number the day we look at it.
Call and you get Beto Ponce, not a call center. Or look through the gallery first.
(919) 440-1333