Resin floors across Sampson County.
Clinton and the surrounding communities, including Ivanhoe and the smaller crossroads. Poured by the owner, ground down to clean concrete first.
Insured and bonded · 5 years · every floor poured by the owner
Get a free quote
Photos and rough square footage get you a real number.
What we install around Sampson County.
Clinton and the surrounding communities, including Ivanhoe and the smaller crossroads.
Clinton sits about 40 minutes from the shop in Goldsboro, well inside the 60 mile radius we cover. We cover Clinton and the communities between them: Clinton, Newton Grove, Turkey, Autryville, Garland, Salemburg, Roseboro.
Garages are the bulk of the work, but a good share of what we pour in Sampson County is countertops, because resurfacing a kitchen costs a fraction of replacing the counters and takes two or three days instead of two weeks.
Whatever the room is, the sequence does not change. We grind the slab down to open concrete, fix what the grind exposes, then pour. Read more about how we prep concrete or tell us what you are looking at.
Towns we cover in Sampson County
Work from around the county
Which floor belongs in which room.
Flake is the workhorse. Vinyl chip broadcast into the base coat and locked under a clear topcoat, it hides tire marks and dust and gives you grip when the floor is wet. Most garages around Sampson County end up here once people have seen both options in person.
Metallic is the showpiece. Pigment moves while the resin cures, so the pattern is decided in the twenty minutes the floor is still workable and no two come out the same. Quartz is the toughest thing we install, graded sand set in resin with slip resistance built into the texture, and it belongs in laundry rooms, workshops, and anywhere water and traffic show up together.
Countertops are their own category. The resin pours over the counters you already have, so a kitchen changes completely without a tear-out. Read more on the countertops page.
What we pour
What the ground here does to a slab.
This is coastal plain country. Sandy soil, a water table that moves with the season, and eight months a year of real humidity. Slabs poured on that ground shift a little, and the hairline cracking that comes with it is normal rather than alarming. What matters is catching it during the grind and filling it, instead of coating straight over it and watching it telegraph through the finish six months later.
The bigger issue is vapor. A lot of the housing stock around Sampson County went down without a vapor barrier under the slab, because for years that was normal practice. Those floors push moisture upward every day, and a coating that cannot breathe traps it and lifts. We test before quoting. If a slab is too wet for the system you want, we will say so and price something that can handle it.
How a job in Sampson County runs.
Everything comes out on a trailer: grinders, dust extraction, mixing gear and material. Day one is prep, which is the loud and dusty half. Day two is the pour. You can walk on it the next morning and put a vehicle back on it in three to four days depending on temperature.
The garage needs to be completely empty the morning we start, because we have to grind the whole slab. That is the one piece of the job that falls on you, and it is worth doing the weekend before rather than the morning of.
Questions from Sampson County customers
Do I have to coat it after grinding?
No. Plenty of people grind and seal and stop there, especially on a shop floor or a slab they like the look of. Grinding is a service on its own, not only a step toward a coating.
Will grinding get rid of the oil stains?
Mostly, yes. Grinding takes off the top layer where the stain sits. Oil that has soaked deep can work its way back up, so a badly stained slab gets degreased first and may get a primer too.
How much dust does it make?
Less than you would think. Each grinder is hooked to a dust extractor, so the dust gets pulled in right where the tool makes it. Some still gets out, but the house does not fill up with it.
How long does a garage floor take?
The work itself is two days on most two-car garages, and the slower part is the curing. You can walk across it the morning after we coat it. Parking has to wait three to four days. Day one of the job is the grind and prep, day two is the coating.
Do I have to empty the garage?
Yes, completely. We need the whole slab open to grind it. Plan on the garage being empty the morning we start and staying empty until the floor takes weight.
Working in Sampson County this month.
Send a photo of the slab and the rough size. You get a number the day we look at it.
Not ready to call? Browse the gallery first. When you do call, you talk to Beto Ponce, the owner.
(919) 440-1333