Floors worth looking down at, Calypso.
Resin floors and countertops around Calypso, poured by the owner, Beto Ponce. Insured and bonded, with metallic work as the specialty.
Insured and bonded · 5 years · every floor poured by the owner
Get a free quote
Photos and rough square footage get you a real number.
Resin floors for Calypso homes.
Most of the garages we coat around Calypso were poured with the house and never touched since.
We run out to Calypso from the shop in Goldsboro, about 40 minutes out. Calypso is in Duplin County, and we cover the towns around it too, including Faison, Warsaw, Kenansville, Magnolia.
Concrete is porous. It drinks oil, it dusts under tires, and once a stain is in there it stays. A resin floor closes the slab off for good.
We own the grinders outright. Renting by the day puts a clock on the most important step, and the grind is the step that decides how long the floor lasts. So it goes the same way on every job: diamond grind to open concrete, chase and fill whatever cracks appear, then pour and topcoat. No shortcuts in the first half.
The ground under a slab in Calypso.
Slabs out here sit on sandy soil over a water table that rises and falls, and they get eight months of real humidity on top of that. All of it keeps the concrete moving slightly, so fine cracking is expected. Coating straight over it is the mistake. We find those cracks while grinding and fill them before any resin goes down.
Vapor drive is the bigger issue. A lot of the housing stock here went down before vapor barriers under slabs were standard practice, so those floors move moisture upward every single day. Trap that under a coating and it lifts. We test for it up front, because finding out afterward is expensive for everybody.
Five years of pouring in this climate teaches you how heat changes resin. The same metallic floor behaves one way in an uninsulated garage in August and another way in October, and the difference shows up right in the pattern. Knowing which one you are walking into is a big part of the job.
What we pour in Calypso
Recent pours
Which rooms we end up in.
The rooms change but the problem does not. Bare concrete is porous, it stains, it dusts, and sealing it after the fact with something off a shelf almost never holds.
The metallic work that people notice on our floors goes on countertops too. Beto pours it right over the existing counters in your Calypso kitchen, so the cabinets stay and nobody cooks on plywood for a week while stone gets cut. Read what a countertop job involves for the details.
Timing a pour around the weather.
We pour most of the year. What moves a date is slab temperature, not the calendar, so a mild January week is often better than a brutal July afternoon.
What moves the price.
The honest answer on price is that we cannot give one over the phone and mean it. Two rooms the same size can be a long way apart once you know what is under the old coating.
So we come look at the floor in person. You get a firm number on the day of the visit, and it does not creep up once the grinders are running. If you would rather check the range first, photos of the slab are enough for a rough yes or no.
How the two days run.
Day one is prep. Grinders and dust extraction come off the trailer and the slab gets taken down to clean concrete, then the cracks and pits that the grind exposes get chased out and filled. It is loud and it is dusty, and it is most of the labor in the job. Day two is the pour and the topcoat, which is the fast half.
Everything has to come off the floor before we get there, shelving and all. The grinder covers the whole slab edge to edge, so an empty room on the first morning is the one thing we ask for. After the topcoat you can walk on it the next day. Driving on it waits until day three or four.
Who actually pours it.
Alpha Resin is a small shop on purpose. Fewer floors, poured by the person whose name is on the truck.
Insured and bonded, 5 years of pours, and a phone the owner answers. See the gallery, read about the rest of Duplin County, or send photos of the slab.
The same person who answers the phone drives the trailer out, so the question of whether we come to you is easy to settle. Calypso is well within the 10 counties we cover from Goldsboro. If you are a few miles beyond town, call before you assume we will not come. Town limits rarely line up with the real drive.
Questions from Calypso customers
Do I have to empty the garage?
Yes, completely. We need the whole slab open to grind it. Plan on the garage being empty the morning we start and staying empty until the floor takes weight.
Will it peel like the kit I bought at the store?
Store kits fail because they go over sealed concrete with no mechanical prep. We grind the slab open first, which is what lets the resin key into the concrete instead of sitting on top of it.
Can you coat a floor that already has something on it?
Usually. Old paint, failed sealer, and most previous coatings come off in the grind. If there is a moisture problem underneath we will tell you before we quote it, not after.
Is it slippery when wet?
Wet, a smooth finish is slippery. That is why pool decks, patios and garages usually get an aggregate broadcast into the topcoat, which gives the surface texture to grip. Tell us where the floor is going and we will add it.
How much does a floor cost?
That comes down to your floor. Square footage is part of it, the slab’s condition is a bigger part, and metallic, flake or quartz each prices differently. We quote in person. The number is (919) 440-1333.
Got a slab in Calypso?
Photos plus an approximate square footage gets you a straight answer on what the floor will take.
Beto Ponce picks up when you call. If you want to see his floors first, the gallery has plenty.
(919) 440-1333